- Вы можете использовать опцию И / ИЛИ / НЕ для критериев, которые вы хотите добавить или. - Вы можете вернуться к обычному поиску, нажав кнопку Отмена.
In this research work, a new harmonic responsibility measure is proposed to extract the amount of harmonic responsibility of each plant supplied from the point of common coupling (PCC). The proposed method uses a function of the correlation coefficients between the voltage and current signals measured synchronously at the PCC. After the verification of the method on synthetic data generated in simulation environment, field data measurements of voltage and current are used to test the practicability of the proposed method. Harmonic contributions of the iron and steel (I&S) plants obtained using ...Более
An efficient methods for the synthesis of 2-(2,5-dimethylphenyl)-3-iodobenzo[b]thiophene (4) is described, and investigated its anode catalyst performance by using electrochemical methods (CV, CA and EIS). When 2-(2,5dimethylphenyl)-3-iodobenzo[b]thiophene (4) is applied, the specific activity is found as 25.811 mA/cm(2). Interestingly, when Palladium (Pd) is electrochemically deposited on the benzothiophene derivative, the catalytic activity increased the 80.930 mA/cm(2). This result is highest than the current metal based anode catalyst. Moreover, EIS and CA measurements display that Pd dope ...Более
This paper presents a research work which focuses on generating synthetic data to enrich the training-set of a deep learning (DL) based classification system to classify power system transient events using PMU frequency measurements. The synthetically improved training-set is shown to increase the classification performance compared to the case when only the actual-data training-set is used. The proposed classification system helps to reveal high-frequency transient variation information out of PMU measurements collected at a relatively much lower rate, especially when a small set of training- ...Более
In this paper, a method to generate large amounts of Electric Arc Furnace (EAF) currents with harmonics simulating the actual EAF operation characteristics to be used with deep learning (DL) applications of harmonic estimation is investigated. For this purpose, the behavior of the EAF current harmonics is examined in statistical terms using the field data collected at a transformer substation supplying an EAF plant. Then, a significantly larger amount of EAF current data is generated using the statistics mimicking the real EAF behavior to train the DL-based harmonic estimator. The outcomes of ...Более
In internal combustion engines, mineral engine oils which serve as lubricants between parts are not used alone due to technical reasons and various additives are made use of for better lubrication. In these additives, liquid boron serves to reduce friction. To reduce the environmental damage caused by engine lubrication oils, it is necessary to improve the properties of biological oils so that they can be used and compete with mineral oils technically. In the study, the use of liquid boron as an engine lubrication oil additive, together with wild mustard oil methyl ester, was investigated. Two ...Более
In Turkey, the consumption of diesel oil is increasing both in transportation and in agricultural fields. In this study, the opportunities of the use of safflower oil, which grow originally in Turkey as a direct fuel in diesel engines, were researched to provide a new alternative for biofuel industry and to popularize the farming of oil crops.
In this study, the kit design was completed first, and afterwards safflower oil was exposed to the process of neutralization and laundering, and then turned into standard fuel. For engine performance experiments, reference experiences were conducted by ...Более
In this study, biodiesel was produced from safflower seeds by converting the raw oil obtained through dampening them via the rolling process, roasting at 90 °C and pressing into Safflower Oil Methyl Esther (Safflower Biodiesel) using the trans-esterification method. Experimental fuels were obtained in the forms of D100, B2.5M2.5D95, B5M5D90, B5M2.5D92.5 and B2.5M5D92.5 by mixing the biodiesel fuel obtained from safflower with diesel fuel, adding bio-ethanol at the rates of 2.5% and 5%, and volumetrically in inverse ratio. Tests were conducted to determine the fuel properties of the mixed fuels ...Более
On a power network, events are desired to be monitored to find its reasons and to take preventive action. Today, power quality measurement devices are used to obtain synchronous measurement data of network, however these devices are expensive and it is not considered a practical option to place one on each node of the network. Therefore, methods estimating voltages and currents at non-measured points of the network are required. In this study, a new power system transient state estimation method is designed to estimate transientsin a power network in which some of the loads are unknown. By thi ...Более
In the present work, TiO2 nanotubes (TNT) and carbon-doped TiO2 nanotubes (C-TNT) were produced via the anodization method. Carbon doping was performed on TNT in a tubular oven employing two different 15 cm3/min total flow rates with varying compositions of acetylene (C2H2) and argon (Ar) as VC2H2/Ar = 7/93 (1 cm3/min C2H2 14 cm3/min Ar) for C-TNT (7:93) and VC2H2/Ar = 33/67 (5 cm3/min C2H2 10 cm3/min Ar) for C-TNT (33:67). The synthesized C-doped TNT was characterized by x-ray diffraction (XRD), Raman spectroscopy, and scanning electron microscopy (SEM). XRD, Raman spectra, and SEM result ...Более
A method has been proposed for accurate characterization of non-reciprocal networks without enforcing the passivity principle. Thanks to the introduced different even and odd coefficients, our method has no singularity-point problem as compared with the conventional method. The proposed method is validated by scattering parameter measurements of a ferrite-loaded waveguide shifter. In addition, it is demonstrated by measurements that our method, as compared with the conventional one, is more resistant to random noise due to post-calibration effects.